1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Name: Clean-Air ( mold removal )
Refresher detergent & biocide for Air Conditioning Equipment.
Company Identification: A. Gur Technologies, Israel
For information call: +972 3 6492053 \\  Fax  +972 3 6482892
Emergency Number: Local Health Authority.

2 - COMPOSITION, INFORMATION ON INGREDIENTS

Mixture of detergents and biocide.
Surfactants & Detergents.
Poli oxyethylen (dimethylimino) ethylenedichloride.
Non-ionic surfactant  p-10.

3 - HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW: ( mold removal )
Non-Corrosive compound. May be harmful if swallowed.
Non Toxic.
Sub risk :Non - Corrosive.

Potential Health Effects -
Eye: Irritating.
Skin: moderately irritating.
Ingestion: may be irritating to mouth, throat and stomach.
Inhalation: non - hazardous.

4 - FIRST AID MEASURES

Eyes:

Check for and remove any contact lenses. Immediately flush eyes with running water for at least 15 minutes, keeping eyelids open. Seek medical attention.

Skin:

Flush skin with plenty of soap and water for at least 15 minutes while removing contaminated clothing and shoes. Get medical aid if irritation develops or persists.

Ingestion:

Drink plenty of water. Get medical aid. Do not Induce vomiting.

Inhalation:

Remove to fresh air. Allow the victim to rest in a well-ventilated area. Oxygen may be administered if breathing is difficult. If irritation or difficult breathing persists, seek immediate medical attention.

5 - FIRE FIGHTING MEASURES

Non combustible compound.
Use suitable extinguishing media - Water spray, CO2, Foam.
Wear appropriate protective clothing.
Mount respiratory protective device, if necessary.
When heated to decomposition, may emit toxic fumes of Na2O.

6 - ACCIDENTAL RELEASE MEASURES

7 - HANDLING and STORAGE

Handling: ( mold removal )

Handle with care.  Wash thoroughly after handling.
Avoid contact with skin and eyes. Avoid breathing.
Avoid contact with clothing.

Storage: ( mold removal )

Store in a tightly closed container.
Store in a cool, dry, well-ventilated area, away from incompatible substances as explosives.

8 - EXPOSURE CONTROLS, PERSONAL PROTECTION

Engineering Controls: ( mold removal )

Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of vapors below their respective threshold limit value.

Personal Protective Equipment: ( mold removal )

Eyes: No special precautions are necessary if used as intended.

Skin: No special precautions are necessary if used as intended.

Clothing:  No special precautions are necessary if used as intended.

Respirators: No special precautions are necessary if used as intended.

9 - PHYSICAL AND CHEMICAL PROPERTIES

Physical State:              liquid

Appearance:                 Yellow to light Yellow

Odor:                             Pleasant

pH:                                 7

Vapor Pressure:            ab. 5 mm at 20 cen grade

Boiling Point:                  > 100 c.g

Evaporation rate            < 1   ( BuAc = 1 )

Flash Point :                    Not Applicable

Solubility:                        Soluble in water

Specific Gravity/Density:   1.00

10 - STABILITY AND REACTIVITY

Normally stable. ( mold removal )
Conditions to Avoid: Incompatible materials, sunlight & heat.
Incompatibilities with Other Materials: Alkaline light metals ( as Zn , Al ) & reactive organic compounds.
Hazardous Polymerization: Will not occur.
 

11 - TOXICOLOGICAL INFORMATION

Non toxic.
IARC carcinogenic category - none
Epidemiology:   No data available.

12 - ECOLOGICAL INFORMATION

No data available.

13 - DISPOSAL CONSIDERATIONS

Dilute with water. ( mold removal )
Dispose of in a manner consistent with local regulations.
Transfer to a licensed disposal contractor.

14 - TRANSPORT INFORMATION

US DOT – domestic   Not-regulated
IMO - international

15 - REGULATORY INFORMATION

Reported \\ included on the EPA TSCA inventory list.
Community Right To Know list.
Label:

16 - ADDITIONAL INFORMATION

According to EC Directive 91/155/EEC.
MSDS Creation Date:2001. Amendment, by d.k. Revision: 2 , Oct 2002.
The information above is believed to be accurate & represents the best information currently available to us. However, we make no warranty of merchantability or any other warranty, express or implied, with respect to such information, and we assume no liability resulting from its use.
Users should make their own investigations to determine the suitability of the information for their particular purposes.
In no way shall supplier be liable for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, consequential or exemplary damages, howsoever arising, even if has been advised of he possibility of such damages.